Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Cap & Crown for Borough Park Homeowners
A missing or rusted-out cap is the single most common reason water gets into a Borough Park chimney. Once rain runs down the flue, it soaks the masonry, works into the smoke chamber, and starts the slow freeze-and-spall cycle that turns a small repair into a rebuild. A proper cap and a sound crown stop that at the top, before it starts.
Our technicians have up to 9 years of experience, and we work from an inspection first, recommendation second discipline: we photograph the crown, the cap, and the flue top, then show you what we found before anyone quotes a repair. Borough Park homes are mostly pre-war brick rowhouses and semis with shared or closely spaced flues, and that layout changes what cap fits and how the crown has to be poured.
We work with trade-grade brands like Gelco, Olympia Chimney, and Copperfield, so what goes on your roof is the same material specified by chimney professionals elsewhere. Call (833) 554-1032 to book a look at your chimney top. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
What Our Chimney Cap & Crown Service Includes
Caps and crowns fail differently, and the fix is different for each. Here is what each part of the job covers.
Cap Installation
A chimney cap is the screened lid that sits over the flue opening and keeps rain, birds, squirrels, and leaves out while letting smoke escape. You need one if your flue is open to the sky, if you’ve heard scratching or nesting sounds, or if water stains show up on the damper or firebox ceiling after rain. We measure the flue, set a stainless or galvanized cap with the correct mesh size for your fuel type, and secure it against wind lift. The cap is anchored to the flue tile or to a leg kit, never just set on top.

Cap Replacement
Caps don’t last forever. Galvanized steel rusts through, mesh rusts shut, and storm-blown branches bend the frame until it no longer seals. You need a replacement when the mesh is clogged solid with soot and rust, when the cap sits crooked, or when the top plate has holes. We pull the old cap, check the flue tile underneath for cracks the old cap may have been hiding, and fit a new one that matches the flue’s actual dimensions rather than a one-size approximation.

Crown Repair
The crown is the concrete or mortar slab at the very top of the chimney that sheds water away from the brick. Hairline cracks are normal; open cracks, a crown pulling away from the flue, or chunks missing are not. When water gets past a failed crown it soaks into the brick below and shows up as efflorescence, spalling faces, or a damp patch on the ceiling near the chimney breast. We remove the failed material, rebuild the crown with the correct slope away from the flue, and bond the new edge so it doesn’t pull free at the overhang.

Crown Coating
Crown coating is a flexible, elastomeric membrane applied over a crown that’s cracked but still structurally sound. It’s the right call when the slab is intact and level but the surface has opened up with fine cracks that let water in. We clean and prep the crown, fill the cracks, and coat the whole surface so it moves with the masonry instead of cracking again. Coating is not a fix for a crown that’s crumbling or separated; in that case we tell you so and quote a repair instead.
Multi-Flue Cap
Many Borough Park rowhouses run two or more flues side by side: one for the fireplace, one for the boiler or water heater. A multi-flue cap covers the whole chimney top in one unit, which is stronger against wind and keeps water off the masonry between the flues. We build these to the exact footprint of your chimney, with a screened opening over each flue and a solid top plate that overhangs the crown edge. On shared chimneys between adjoining homes, we make sure the cap lands on your side of the party wall.
Custom Cap
Some chimneys don’t fit a stock cap. Oversized flues, unusual tile arrangements, and crowns that are wider than standard all need a fabricated unit. We take measurements on site, including the crown’s outside dimensions, the flue tile size, and the height of the tile above the crown. Then we have a cap built to fit that chimney and nothing else, which is what stops the wind-driven rain that a loose stock cap lets in. If a stock cap fits well, we’ll say so and quote that instead.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Cap & Crown
We install and service specific trade-grade brands because the material and the fit are what hold up through a New York winter. Gelco caps and crown products are built for masonry chimneys, and we know where their frames tend to loosen at the leg brackets after years of freeze-thaw. Olympia Chimney makes cap and crown components we fit on both single-flue and multi-flue chimneys, and we’ve learned which of their sizes work best on the tight tile spacing common in older Borough Park brickwork. When an existing Gelco or Olympia cap is salvageable, we’ll clean and reseat it rather than push a replacement.
Famco and Copperfield round out the brands we handle most, and each has its own installation habits worth knowing. Famco caps are straightforward to anchor but need the correct mesh for wood versus gas, since a fine mesh clogs fast on a wood fire. Copperfield copper caps age well and look right on a brick rowhouse, but they need solid framing underneath so the weight doesn’t pull the flue tile loose over time. Whether you have a Gelco, Olympia Chimney, Famco, or Copperfield cap, or any other make, we can help.
Signs You Need Chimney Cap & Crown Right Now
- Water stains on the damper or firebox ceiling. Rain coming down an uncapped flue leaves rust streaks and dark water marks, and it corrodes the damper assembly faster than anything else. If you see them after a storm, the cap is the first thing to check.
- Rust flakes or a clogged screen at the top. A cap whose mesh has rusted shut traps smoke and backs it up into the room, and a rusted-through top plate is no longer shedding water. Both mean replacement, not a cleaning.
- Visible cracks or a separated crown. Look at the mortar slab at the top with binoculars. A crown pulling away from the flue, or a crack wide enough to hold a coin, is letting water into the brick below and will worsen with each freeze.
- White powdery staining on the chimney’s exterior brick. That chalky bloom, called efflorescence, is water pushing salts out through the brick. It usually points to a failed crown or cap letting moisture in from above.
- Birds, squirrels, or nesting debris in the flue. An open flue is an invitation. Nesting material blocks the draft and is a fire hazard, and it’s a strong sign there’s no cap doing its job.
Our Chimney Cap & Crown Process – Step by Step
- 1
Inspection first. We start with a formal chimney inspection, not a quick glance from the ladder. That means a look at the flue interior with a camera where needed, the crown, the cap, and the masonry below the roofline. You get photos of what we found.
- 2
Written findings and options. We explain what’s failing, whether it’s the cap, the crown, or both, and whether a coating would hold or a full repair is warranted. Nothing gets recommended without a photo you can see for yourself.
- 3
Measurement and material selection. We measure the flue tile and crown footprint, then quote a cap built to fit, choosing the mesh size for your fuel and the material for your roof exposure. Brand and model go in the written estimate.
- 4
Installation. On the day, we protect the roof surface, remove the old cap or failed crown material, and set the new component with proper anchoring and the correct slope away from the flue. We check the flue tile for cracks before the new cap goes on.
- 5
Final check and walkthrough. Before we leave, we confirm the cap is secure against wind, the crown sheds water, and you have close-up photos of the finished work. If we found anything else worth watching, we tell you now rather than later.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Cap & Crown Cost in Borough Park?
Most chimney cap and crown work in Borough Park falls into a predictable range, and a written estimate sets the final figure. Here are typical numbers for the common scenarios:
| Work | Typical Estimated Range |
|---|---|
| Single-flue cap, stock size | $175 – $425 |
| Custom-fabricated cap | $350 – $850 |
| Multi-flue cap | $450 – $1,100 |
| Crown coating | $350 – $800 |
| Crown repair or rebuild | $500 – $1,500 |
What moves the number: the size and number of flues, whether the cap is stock or custom, the material (stainless, galvanized, or copper), how high the chimney sits above the roofline, and whether the crown needs a partial repair or a full rebuild. A rowhouse with two flues and an accessible roof is a simpler job than a tall chimney on a steep Mansard roof. You avoid overpaying by getting the inspection photos first and quoting only what’s actually failing; a coating is cheaper than a rebuild, but only when the slab underneath is sound enough to coat.
Every estimate is free and per job. It itemizes the material brand and model, the labor, and any masonry work needed, so you can compare line by line rather than against a single lump figure. If the work can safely wait until after the heating season, we’ll tell you that too.
Chimney Cap & Crown Near Borough Park – Our Service Area
We handle chimney cap & crown work across Borough Park and the neighboring Brooklyn neighborhoods: Sunset Park, Kensington, Dyker Heights, Bensonhurst, Midwood, Bay Ridge, Flatbush, Flatlands, Gravesend, Park Slope, and Carroll Gardens. Roof types and flue layouts shift from block to block, and we plan for that when we quote. Response across these areas is quick, and we confirm the appointment when you call. If you’re outside this list, call and we’ll tell you straight whether we cover it.
Serving Borough Park, NY – Our Local Coverage Area
We serve Borough Park and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Cap & Crown in Borough Park
A chimney cap is the screened cover over the flue opening that keeps out rain, animals, and debris, while the crown is the concrete slab at the top of the chimney that sheds water off the brick. You need both in good condition because they protect different parts of the chimney: the cap guards the flue, the crown guards the masonry. A failed cap lets water into the flue; a failed crown lets it into the brickwork. Call (833) 554-1032 for an exact quote – estimates are free.
A stock cap installation usually takes about an hour once we’re on the roof, while a custom or multi-flue cap and a crown repair can run most of a day. Crown work that involves removing and rebuilding the slab takes longer than a coating because the new material needs to be shaped and sloped properly. We give you a time window with the estimate so you can plan. Call (833) 554-1032 and we’ll quote your specific job.
A typical cap installation in Borough Park runs $175 – $425, a crown coating runs $350 – $800, and a crown repair or rebuild runs $500 – $1,500, with the written estimate setting the final price. The range depends on flue count, cap material, and whether the crown is coated or rebuilt. We itemize the brand, materials, and labor so you can see exactly what you’re paying for. Call (833) 554-1032 for an exact quote – estimates are free.
Yes. We install, replace, and service caps and crown components from Gelco, Olympia Chimney, Famco, and Copperfield, and we know where each tends to wear out. If your existing cap is from one of these brands and still structurally sound, we’ll reseat or clean it rather than push a new one. Whether you have one of these makes or any other brand, we can help. Call (833) 554-1032 to book a look.
Yes, we offer same-day caps and crown work when the schedule allows. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday; a call outside dispatch hours is booked into the next opening. The urgency here is seasonal: getting a cap on before the first hard freeze protects the brick from water damage over the winter. Call (833) 554-1032 to book.
We stand behind the installation and confirm the workmanship and material terms in writing on your estimate before any work begins. A properly installed cap and a correctly sloped crown are meant to hold for years, and we back that with a satisfaction guarantee. If something we installed fails, you call us and we make it right. Call (833) 554-1032 to discuss your job.
Clear access to the chimney, indoors and out, and make sure someone is home to let us in if we need interior access. Move anything fragile away from the fireplace area, and note any leaks or stains you’ve seen so we can check those spots. If you have pets, secure them while we’re working. Call (833) 554-1032 to confirm details for your appointment.
Schedule Your Chimney Cap & Crown Service in Borough Park Today
A failed cap or crown gets worse with every freeze, and it’s one of the simpler problems to fix when you catch it early. We’ll inspect, show you the photos, and quote a per-job estimate with the material brand spelled out. Call (833) 554-1032. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. The estimate is free and there’s no obligation. We can also set you up with a chimney repair inspection if the masonry below needs a look.
Written by the team at Chimney Sweep Borough Park.